. Instructions for installing modern plumbing systems. EVER-READY STREET ELBOW. Working Plan No.. SEARS, ROEBUCK AND CO., CHICAGO. 25 ^-?^

RMID:2AG5H8D

Preview

Buy the print

Image details

Contributor:

The Reading Room / Alamy Stock Photo

Image ID:

2AG5H8D

File size:

7.1 MB (253.1 KB Compressed download)

Releases:

Model - no | Property - noDo I need a release?

Dimensions:

1292 x 1934 px | 21.9 x 32.7 cm | 8.6 x 12.9 inches | 150dpi

More information:

This image is a public domain image, which means either that copyright has expired in the image or the copyright holder has waived their copyright. Alamy charges you a fee for access to the high resolution copy of the image.

This image could have imperfections as it’s either historical or reportage.

Search stock photos by tags

bookcentury1900 bookdecade1920 booksubjectdivisio bookyear1922

Similar stock images

RM2AG5HJC–. Instructions for installing modern plumbing systems. I CHECK.I 5HOR TI UNION. EVER-READY STREET ELBOW

RM2AG5FEK–. Instructions for installing modern plumbing systems. Working Phm, Ouifits !,!—2637y2 to &—8644J&. PRESSURE QAuqE-£ CHECK AND WASTE-. ?RESSURE REQULA Tirjq crLirJOER. READY | STREET ELBOW

RM2AG5FXX–. Instructions for installing modern plumbing systems. I STREET ELBOW. Working Finn No. U. >YA TER C YL INOER 26 SEARS, ROEBUCK AND CO., CHICAGO.

RM2AG5FP3–. Instructions for installing modern plumbing systems. Working Finn No. U. >YA TER C YL INOER 26 SEARS, ROEBUCK AND CO., CHICAGO.. Working Phm, Ouifits !,!—2637y2 to &—8644J&. PRESSURE QAuqE-£ CHECK AND WASTE-. ?RESSURE REQULA Tirjq crLirJOER

RM2AG5NHG–. Instructions for installing modern plumbing systems. below the drain pipe from thebathtub, and when this last piece of pipewith the elbow on the end is screwed intothe street elbow in the bottom of the drumtrap, you have finished the roughing-in ofthe waste pipe for both bathtub and lava-tory. Supply Pipes to Fixtures It will hardly be necessary to go into thedetails of the installation of the supplypipes in this installation, except to call at-tention to the fact that we illustrate thelavatory with the supply pipes to the floor.Therefore, the supply pipes leading to thebathtub and lavatory

RM2AG5BGB–. Instructions for installing modern plumbing systems. ter bed, where the liquid is finallydisposed of, time between emptyings to dryand air out. The time between dischargesdepends on the size of the siphon compart-ment, and should be regulated by the kindof soil or filter into which the liquid is run.If the soil is a heavy loam with poor naturaldrainage, there should be more time betweendischarges; therefore the second compart-ment should be larger. If the soil is veryporous, or there is a decided fall to the landand the natural drainage is good, the dis-charge can be more frequent, and so th

RM2AG59B7–. Instructions for installing modern plumbing systems. er partis working. The main distributing trough at the headof the bed should be made of lx6-inch lum-ber, when serving six persons. The sizeshould be increased when more are served. - iium mm mi mum minim mil limn miiiiii m mini iiiiiniiiiiiiiiiiiiiii iiiiiiiiniii iiimiiimiiiimiiimmiiiiiii n uiiiiuuuiiimuiuumiiuiuuuiimiuiuiiiiitiuumiiiiiiiiimiimimmimii uuiuiiiiuiiiuiimniuj inmiii iiiiiimiimmimiiii| | Hercules Septic Tank Siphon Hercules Siphons are made of cast iron and have no moving parts; they| intended for use with the septic tanks des

RM2AG61C4–. Instructions for installing modern plumbing systems. Photo No. 11. you already know, is called roughing-in.Where the water supply pipes are not to beconcealed, it is not necessary to put themin when other roughing-in is being installed.It is much easier to install the supply pi])eswhen they are left exposed. Where this isdesirable the fixtures can be connected tothe waste piping and set in position beforerunning the hot and cold water supply pipesto them. If the fixtures you install have the supplypipes to the floor instead of to the wall(those in Installation No. 1 have the sup-ply pipes to

RM2AG5ARG–. Instructions for installing modern plumbing systems. e top. In the eighteen to twenty-four hours that the sewage should remainin the settling compartment, it is nearly allturned into liquid form, and then runsover into the second or siphon compart-ment, which should have a manhole cover,42—1709 %, with holes to admit air. given with the understanding that the inletpipe and the pipe connecting the two com-partments shall be 12 inches below the topof the tank, so that the surface of thesewage will be 12 inches below the tankroof. These dimensions may be variedslightly to suit local conditions,

RM2AG5EYB–. Instructions for installing modern plumbing systems. h thepump platform, as explained in the discus-sion of hvdropneumatie cylinders on page24. The cylinder rod can be connected tocoupling in hydropneumatic cylinder byraising handle of pump; this will force therod down to the full length of the stroke,namely, 10 inches, and the rod and couplingcan then be securely screwed together. Thepump rod from the top of the pump downto the water cylinder should be screwed to- .gether tight so there will be no possiblechance of lost motion, which would causehammering, and soon destroy the threads onthe

RM2AG5X4F–. Instructions for installing modern plumbing systems. e the tub upon its legs carefully,being sure not to strike the waste pro-jection on the bottom, and slip the wasteprojection into the top of the tub trap.The top rim of the trap should be lined withputty to make it watertight. Bolt the trapto the tub by the short bolts that come withit. Put the heads of the bolts into the slotson either side of the connections and screwup the nuts against the trap. The two extranuts are used to lock the first, so that therewill be no possible chance for them toloosen. If you use compression (stub) laundryt

RM2AG5XDK–. Instructions for installing modern plumbing systems. end ofthe nickel plated tee over the drain pipeextending up from the floor. Tighten upthe three coupling nuts to the overflow pipe,the strainer pipe and the pipe in the floor.Then attach the supply pipes to the faucetswith the union nuts, and the tub is complete. Installing the Laundry Tub Our description is for the tub in InstallationNo. 1, on page 3. The principles of thisinstallation are correct for any laundry tub. The first thing to do is to screw the tubtrap into the drainage tee that we assumehas already been installed to take careo

. Instructions for installing modern plumbing systems. EVER-READY STREET ELBOW. Working Plan No.. SEARS, ROEBUCK AND CO., CHICAGO. 25 ^-?^

Image details

Search stock photos by tags

Get great features with your free account

Get inspired for your next project!